cyrusia

Namalsk missions not spawning

7 posts in this topic

How do you get the missions to spawn on namalsk? They spawned fine in the beggining but after a while they just flat out stopped spawning, is it the player flags blocking them? Anyone can help?

1 person likes this

Share this post


Link to post
Share on other sites
Advertisement

Do you have any errors in the RPT logs?

Sometimes you do need to run the debug mode on DMS just to find out whats going on as it shows when it just cant place a mission (line 13 of main config)

You could also try dropping some of the mission blacklist setup:

Quote

 DMS_PlayerNearBlacklist    = 1500;      // Missions won't spawn in a position this many meters close to a player
 DMS_SpawnZoneNearBlacklist   = 2000;      // Missions won't spawn in a position this many meters close to a spawn zone
 DMS_TraderZoneNearBlacklist   = 2500;      // Missions won't spawn in a position this many meters close to a trader zone
 DMS_MissionNearBlacklist   = 2500;      // Missions won't spawn in a position this many meters close to another mission
 DMS_WaterNearBlacklist    = 500;      // Missions won't spawn in a position this many meters close to water
 DMS_TerritoryNearBlacklist   = 100;      // Missions won't spawn in a position this many meters close to a territory flag

turn those down a little plus you could also try adjusting the retry:

Quote

 DMS_ThrottleBlacklists    = true;      // Whether or not to "throttle" the blacklist distance parameters in DMS_fnc_FindSafePos. This will reduce the values of the minimum
                  //distances for some of the below parameters if several attempts have been made, but a suitable position was not yet found. This
                  //should help with server performance drops when spawning a mission, as DMS_fnc_findSafePos is the most resource-intensive function.

DMS_AttemptsUntilThrottle   = 10;      // How many attempts until the parameters are throttled.

turn this one down a little to say 6-8 as it will lessen the amount of tries before placing with a reduced % of the 1st set of blacklists, then try

Quote

  DMS_ThrottleCoefficient    = 0.8;      // How much the parameters are throttled. The parameters are multiplied by the coefficient, so 0.9 means 90% of whatever the parameter was.
 DMS_MinThrottledDistance   = 100;      // The minimum distance to which it will throttle. If the throttled value is less than this, then this value is used instead.

I turned this down from 0.9 to 0.8 but you could try lower.

This would reduce the amount of clear space required for a mission to spawn

Share this post


Link to post
Share on other sites

Hey there, I'm one of the owners of this community and this is "just" a user, a amazing user to say the least.

But yes, we're not having ANY errors, we're just guessing because of the size of the map and how DMS security safe spawning is working.

According to the RPT everything loads but nothing spawns, and no errors.

We're going to reduce all the blacklist to a really low number and try. 

Share this post


Link to post
Share on other sites

Posted (edited)

Disregard post, I didn't read it all the way through xD

Edited by ka0s

Share this post


Link to post
Share on other sites
20 hours ago, red_ned said:

Do you have any errors in the RPT logs?

Sometimes you do need to run the debug mode on DMS just to find out whats going on as it shows when it just cant place a mission (line 13 of main config)

You could also try dropping some of the mission blacklist setup:

turn those down a little plus you could also try adjusting the retry:

turn this one down a little to say 6-8 as it will lessen the amount of tries before placing with a reduced % of the 1st set of blacklists, then try

I turned this down from 0.9 to 0.8 but you could try lower.

This would reduce the amount of clear space required for a mission to spawn

Hello.

I try this but mission not spawning...no RPT error.Any idea why?

Thank you.

Share this post


Link to post
Share on other sites
Advertisement

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.